联系我们
公司名称：XXX
电话：XXX
手机：XXX
联系人：XXX
地址：XXX
新闻动态
如何安装使用实木压纹机
压纹机底脚有四个螺栓孔，待设备摆放好后，使用膨胀螺丝固定底脚。
There are four bolt holes on the foot of the embossing machine. After the equipment is put in place, the expansion screws are used to fix the base.
设备出厂前各减速机、润滑点均已添加润滑剂、润滑油等。用户在日常使用中按规定正常维护保养即可。
Lubricants and lubricants have been added to the reducer and lubrication points before the equipment is released. Users can maintain normal maintenance according to the regulations in daily use.
润滑液添加具体操作按以下方法：
The specific operation of lubricating fluid is as follows:
1.打开大罩壳，将减速机的注油孔和透气孔打开，加注32号齿轮油，注意观察减速机一侧的观察口，当油位到达观察口时即停止加油（冬天温度低，润滑油粘度大，加油过程时间长）。
1. Open the big cover, open the oil injection hole and air permeability hole of the reducer, fill the No. 32 gear oil, pay attention to the observation port on the side of the reducer, and stop refueling when the oil level reaches the observation port (low temperature in winter, high lubricant viscosity, long refueling process).
2.卸油口在观察口下方。换油的时候先打开透气帽，再打开卸油口螺丝，注意在螺丝快卸掉的时候放慢速度，防止油喷溅到身上。
2. the unloading port is below the observation port. When changing oil, first open the breathing cap, then open the screw of the unloading port, pay attention to slowing down the speed when the screw is fast unloading, so as to prevent oil splashing on the body.
3.压纹机与电源接线应牢固安全，接地线应牢固地接在接线盒内接地线柱上，并使机体外壳有良好的接地，电控线路中应安装与所选用电动机相配套的过载等保护装置。
3. The connection between embosser and power supply should be firm and safe. The grounding wire should be firmly connected to the grounding wire post in the junction box, and the body shell should be well grounded. The overload protection devices matching the selected motor should be installed in the electric control circuit.
4.接通电源，启动压辊检查其旋转方向是否正确。应特别注意接线后应点动试车，以防止闷烧电动机。
4. turn on the power and start the press roller to check whether the rotation direction is correct. Special attention should be paid to the commissioning of the wiring to prevent smouldering motors.
5.空载和满载试运转时，压纹机运转平稳，无明显周期噪声，无渗漏润滑油现象。
5. During no-load and full-load commissioning, the embossing machine runs smoothly, without obvious periodic noise and leakage of lubricating oil.
6.压纹机在首次加油后应先空转片刻，待运转正常后方可投料。长期停放后使用也应先空转片刻待运转正常后方可投料。
6. the embossing machine should be idle for the first time after the first refueling. After a long period of parking, it should be idle for a moment before the operation is normal.
7.物料的投放应缓慢、均匀，避免冲击载荷。
7. material delivery should be slow and even to avoid impact load.
8.生产过程中，应尽量避免频繁起动和过载运行，压纹机一旦发生故障，应立即断电检查，予以排除。
8. In the production process, frequent start-up and overload operation should be avoided as far as possible. Once the embosser breaks down, it should be checked and eliminated immediately.
9.生产人员应严格遵守操作注意事项（见设备本体），以免发生安全事故。
9. production personnel should strictly observe the matters needing attention in operation (see equipment noumenon), so as to avoid any safety accidents.
There are four bolt holes on the foot of the embossing machine. After the equipment is put in place, the expansion screws are used to fix the base.
设备出厂前各减速机、润滑点均已添加润滑剂、润滑油等。用户在日常使用中按规定正常维护保养即可。
Lubricants and lubricants have been added to the reducer and lubrication points before the equipment is released. Users can maintain normal maintenance according to the regulations in daily use.
润滑液添加具体操作按以下方法：
The specific operation of lubricating fluid is as follows:
1.打开大罩壳，将减速机的注油孔和透气孔打开，加注32号齿轮油，注意观察减速机一侧的观察口，当油位到达观察口时即停止加油（冬天温度低，润滑油粘度大，加油过程时间长）。
1. Open the big cover, open the oil injection hole and air permeability hole of the reducer, fill the No. 32 gear oil, pay attention to the observation port on the side of the reducer, and stop refueling when the oil level reaches the observation port (low temperature in winter, high lubricant viscosity, long refueling process).
2.卸油口在观察口下方。换油的时候先打开透气帽，再打开卸油口螺丝，注意在螺丝快卸掉的时候放慢速度，防止油喷溅到身上。
2. the unloading port is below the observation port. When changing oil, first open the breathing cap, then open the screw of the unloading port, pay attention to slowing down the speed when the screw is fast unloading, so as to prevent oil splashing on the body.
3.压纹机与电源接线应牢固安全，接地线应牢固地接在接线盒内接地线柱上，并使机体外壳有良好的接地，电控线路中应安装与所选用电动机相配套的过载等保护装置。
3. The connection between embosser and power supply should be firm and safe. The grounding wire should be firmly connected to the grounding wire post in the junction box, and the body shell should be well grounded. The overload protection devices matching the selected motor should be installed in the electric control circuit.
4.接通电源，启动压辊检查其旋转方向是否正确。应特别注意接线后应点动试车，以防止闷烧电动机。
4. turn on the power and start the press roller to check whether the rotation direction is correct. Special attention should be paid to the commissioning of the wiring to prevent smouldering motors.
5.空载和满载试运转时，压纹机运转平稳，无明显周期噪声，无渗漏润滑油现象。
5. During no-load and full-load commissioning, the embossing machine runs smoothly, without obvious periodic noise and leakage of lubricating oil.
6.压纹机在首次加油后应先空转片刻，待运转正常后方可投料。长期停放后使用也应先空转片刻待运转正常后方可投料。
6. the embossing machine should be idle for the first time after the first refueling. After a long period of parking, it should be idle for a moment before the operation is normal.
7.物料的投放应缓慢、均匀，避免冲击载荷。
7. material delivery should be slow and even to avoid impact load.
8.生产过程中，应尽量避免频繁起动和过载运行，压纹机一旦发生故障，应立即断电检查，予以排除。
8. In the production process, frequent start-up and overload operation should be avoided as far as possible. Once the embosser breaks down, it should be checked and eliminated immediately.
9.生产人员应严格遵守操作注意事项（见设备本体），以免发生安全事故。
9. production personnel should strictly observe the matters needing attention in operation (see equipment noumenon), so as to avoid any safety accidents.
