| 压纹机安装和调试工艺 |
| 添加时间：2018/7/4 14:20:28 浏览次数： |
| 压纹机安装和调试工艺 The installation and debugging process of the press grain machine 安装和调试对压纹机的使用寿命及压纹质量有着很大的影响活动，主要需要注意以下几点： Installation and commissioning have great influence on the service life and embossing quality of the embossing machine. 1.压纹机底座要平整、牢固 1. press grain machine base to be smooth and firm 如果压纹机底座不牢固，即使安装时已做了准确的水平校正，但一段时间的运转后基础水平也必将因机器振荡破坏出现变异情况，机器偏斜而导致运行不稳定，从而影响压纹产品质量。 If the pedestal is not strong, even when the installation has been corrected accurately, the base level of a period of time will also cause variation in the failure of the machine oscillation, and the machine deviates and causes the unstable operation, thus affecting the quality of the press. 若机器是放在底层出版动态，需要扎地基时，除考虑机器自重外，还要考虑机器运转时传递到地基上的动载荷，以及车间所在地质的软硬程度，以防止机座下沉变形。 If the machine is in the bottom publishing dynamics, when the foundation is needed, in addition to the machine weight, it is necessary to consider the dynamic load transferred to the foundation when the machine runs, as well as the soft and hard degree of the workshop, in order to prevent the sink from sinking. 机器底部若需垫料喷墨，必须采用抗压强度好的钢板，使底座尽量垫得紧实、均匀，不留大面积的“悬空”状况，防止受压变形。在垫、调机器的平行度过程中，机器的辊筒需反复用水平仪校调平衡北人股份，使整机处于比较水平的状态。网络出版 If the bottom of the machine is needed to spray ink, the steel plate with good compressive strength must be adopted so that the base can be tighten and uniform as far as possible, and the "hanging" condition is not left in large area to prevent the compression deformation. In the process of parallelism between the pad and the machine, the roller of the machine should be adjusted and balanced with the level instrument repeatedly, so that the whole machine is in a relatively horizontal state. Network publishing 2.做好压纹机试运行前后的检查工作 2. do the inspection work before and after the test run of the press grain machine 机器的试运转是一项重要的工作，在此之前要仔细检查各部分零部件是否完整无缺、螺丝是否有松动现象、油路是否畅通(同时要注意给各轴承、传动、滑动部位加注润滑油)、各部位有无卡阻现象、机上微动行程开关是否可靠灵敏，机器周围的杂物也必须全部清理干净。在试运转时应注意：将调速表调至零位档，然后按起动按钮，让机器空运行磨合一段时间包装材料，并注意听机器有无异常响声，确认正常后方可正式进行生产，以确保生产的安全和质量的稳定。 The test operation of the machine is an important work. Before this, we should carefully check whether the parts of each part are intact, whether the screw is loose or not, and whether the oil road is unblocked (at the same time pay attention to the lubrication of the bearings, transmission, sliding parts), the phenomenon of all parts, and the reliability of the micro movement switch on the machine. Min, all the debris around the machine must be cleaned up. In trial operation should be noted: adjust the speed meter to zero gear, and then press the start button, let the machine run in a period of time packing material, and listen to the machine have abnormal sound, confirm the normal production after the normal operation, in order to ensure the safety and quality of production stability. 3.定期检查压纹机的平衡状态 3. check the balance state of the press. 定期对压纹机进行水平状态检查，若发现偏斜情况要及时校平，以免零部件磨损曼罗兰，降低设备的精度和使用寿命。压纹机底座四边各有一只Φ20mm的螺丝，当机器略有不平衡时，可通过调整螺丝进行校平。应注意的是，上螺丝时用力要均匀，若受力不均重组，容易破坏机器的水平状态。 In order to reduce the precision and service life of the equipment, the horizontal state of the press will be checked regularly. If the deviation is found to be leveled in time so as to avoid the wear and tear of the parts, the precision and the service life of the equipment are reduced. There is a 20mm screw on each side of the base of the embossing machine. When the machine is slightly unbalanced, it can be leveled by adjusting screws. It should be noted that when the screw is applied, the force must be uniform. If the force is unevenly reorganized, it will easily damage the horizontal state of the machine. |
| 上一页 压纹机调试和正确操作 |
| 下一页 压纹机的性能特点 |
Copyright © 技术支持：遨游网络