| 压纹机安装和调试工艺 |
| 添加时间：2017/7/26 16:18:17 浏览次数： |
| 1.压纹机底座要平整、牢固 1. The base of the embossed machine should be flat and firm 如果压纹机底座不牢固，即使安装时已做了准确的水平校正，但一段时间的运转后基础水平也必将因机器振荡破坏出现变异情况，机器偏斜而导致运行不稳定，从而影响压纹产品质量。 If embossing machine base is not strong, even if the installation has made accurate level correction, but after a period of running foundation level variation, will appear because of destruction of the machine vibration machine deflection which leads to the instability of operation, thereby affect the embossing quality of the product. 若机器是放在底层出版动态，需要扎地基时，除考虑机器自重外，还要考虑机器运转时传递到地基上的动载荷，以及车间所在地质的软硬程度，以防止机座下沉变形。 If the machine has been published on the underlying dynamics, need firm foundation, in addition to the weight of the machine, but also when the machine is passed on to the foundation of dynamic load, and where qualitative soft hard degree of the plant, in order to prevent the base subsidence deformation. 机器底部若需垫料喷墨，必须采用抗压强度好的钢板，使底座尽量垫得紧实、均匀，不留大面积的“悬空”状况，防止受压变形。在垫、调机器的平行度过程中，机器的辊筒需反复用水平仪校调平衡北人股份，使整机处于比较水平的状态。网络出版 If the bottom of the machine needs to be added to the inkjet, the steel plate must be used to keep the base firmly and evenly, leaving no large area of "hanging" to prevent the compression deformation. In the parallel process of pad and machine, the roller of the machine needs to be used repeatedly to balance the north person's shares with the horizontal instrument, so that the whole machine is in a relatively horizontal state. Internet publishing 2.做好压纹机试运行前后的检查工作 2. Check work before and after the test run of the embossed machine 机器的试运转是一项重要的工作，在此之前要仔细检查各部分零部件是否完整无缺、螺丝是否有松动现象、油路是否畅通(同时要注意给各轴承、传动、滑动部位加注润滑油)、各部位有无卡阻现象、机上微动行程开关是否可靠灵敏，机器周围的杂物也必须全部清理干净。在试运转时应注意：将调速表调至零位档，然后按起动按钮，让机器空运行磨合一段时间包装材料，并注意听机器有无异常响声，确认正常后方可正式进行生产，以确保生产的安全和质量的稳定。 Machine test run is an important work, check each part carefully before this parts are intact, screw loose phenomenon, the oil was clear (and to pay attention to the filling lubricant to the bearing and transmission, sliding parts), each place any jam phenomenon, on the micro switch is sensitive and reliable, all debris around the machine must also be cleaned up. Should be paid attention to during the test run: dispatch control table to zero, then press the start button, and let the machine run empty running in packaging materials for a period of time, and pay attention to machine for abnormal noise, confirmed rear can normal formal production, to ensure production safety and quality stability. |
| 上一页 压纹机开机操作步骤介绍 |
| 下一页 压纹机的安装和调试工艺 |
Copyright © 技术支持：遨游网络